Transmitters with the filling and dosing application pages. Pressure transmitter and flowmeter with protocol 36 pages. Guided wave radar level and interface transmitters pages. Because these products are sophisticated technical instruments, it is important that the owner and operation personnel must strictly adhere both to the information printed on the product nameplate and to all instructions provided in this manual prior to installation, operation, and maintenance.
The Emerson logo is a trademark and service mark of the Emerson Electric Company. Page 5 Warranty 1. Limited Warranty. Subject to the limitations contained in Section 10 Limitation of Remedy and Liability herein, Seller warrants that a the licensed firmware embodied in the Goods will execute the programming instructions provided by Seller; b that the Goods manufactured by Seller will be free from defects in materials or workmanship under normal use and care; CSC Emerson.
Page Section 2: Installation Installation Reference Manual June MAN, Revision 09 Section 2: Installation Unpacking and inspection Carefully remove all of the components from the packaging and verify them against the enclosed packing list. Inspect all components for any obvious damage such as broken or loose parts. If you find any components missing or damaged, notify your local Net Safety representative or the factory immediately.
When determining suitable enclosure orientation for specific applications, installers should observe all local regulations and guidelines for mounting enclosures.
Figure Different enclosure orientations 2. Wiring must comply with all applicable regulations relating to the installation of electrical equipment in a hazardous area and is the responsibility of the installer. If in doubt, consult a qualified official before wiring the system.
The other components of the system — Consult qualified personnel on specific wiring requirements. Figure Non-isolated terminal connection Installation It allows the user to see the concentration of gas present for each individual channel and the various options offered. The display has a wide temperature rating and will operate well in lowly lit conditions. For convenience, a pair of test jacks for each analog output is provided on the front face of the display module.
Each menu option has a submenu, where configuration is completed. Calibrate Sensor? Select Display Selftest Relay? Range Set Alarm Level? Setup Current Date? Setup Current Time? Cal Gas Value Relay Assignment? Refer to Section for the calibration procedure. The default value is channel 1 CH1 enabled for single sensor models model M21 while channel 2 CH2 is permanently disabled.
Apply test gas to confirm alarm level settings. Also see Table 3, Example and Table 4. Activate switch 3, then activate the up key switch 2 , or the down key switch 1 to choose a value. The most recent event will be displayed. Select the up arrow key switch 1 and the down arrow key switch 2 to toggle through all past events. Enable external equipment once testing is completed. The Self-test relay option continuously turns relays on and off to ensure that they are functioning properly.
The Fault Relay is tested first, automatically followed by tests on Relay 1, 2, and 3. Table of Contents. Previous Page. Next Page. Page 2: Important Information Monitoring Inc. Contact Net Safety Monitoring Inc. We welcome your input at Net Safety Monitoring. Page 3: Table Of Contents 4. If the Millennium II Transmitter is installed as Category 3 equipment, then it shall be installed in an Enclosure which maintains an ingress protection rating of IP54 and meets the enclosure requirements of EN Dimensions are in inches and millimeters.
Page 7: Section 1: Installation Carefully remove all components from the packaging and check them against the enclosed packing list. Inspect all components for obvious damage such as broken or loose parts. If you find any components missing or damaged, notify the representative or Net Safety Monitoring, immediately. Figure 4: Rotating Electronics module Note: To access enclosure grounding screw, remove the electronics module by following steps above.
Additional notes: In general, communication cables and power cables should not run in parallel for any significant length, and should not be carried in the same cable tray. Note: If required, use cable glands which have been approved for hazardous locations. Page Remotely Mounted Sensors Jumper Configuration Jumpers and pins are located on the main terminal board near the sensor terminals. JP1 is for channel 1 and JP2 is for channel 2. See Appendix B for information on wire gauge and resistance.
Page Wiring Drawings 2. Consult qualified personnel on specific wiring requirements. Page Installation Checklist Check wiring at all termination and junction points; wiring at transmitter terminals, junction box and at power supply. It allows the user to see the concentration of gas present for each individual channel and the various options offered. The display has a wide temperature rating and will operate well in lowly lit conditions.
Page Status Led Intrusive keeping the enclosure closed and using the magnet and reed switches. There are three visible main menu buttons that are located directly under the display screen. Calibrate Sensor? Page 23 3. See page Activate menu button 3 to display Calibrate sensor. Page Full Calibration Normal Calibration Procedure The following calibration procedure should be followed to ensure an accurate correlation between the output signal and the gas concentration. When the cup is in place, inject calibration gas at a rate of 0.
The default value is channel 1 CH1 enabled for single sensor models while channel 2 CH2 is permanently disabled. Both channels are enabled for two sensor models. Page 29 Under the specific relay with channel, activate the enter key switch 3 to choose the appropriate setting.
See Table 3 below. Page Setup Current Date 1.
0コメント