Omron hc3r pdf

Do not use an inverter output as the power supply. Page 27 5, 1, Reference: A maximum current of 0. Page 28 Output Output Note: 1.

The reset time requires a minimum of 0. This, however, has no effect on the performance of the Timer. Page 32 Control outputs Note: 1. Page 33 5, 1, Reference: A maximum current of 0. In both cases, a life of , operations can be expected. Page 34 Outputs Control output If the time reaches the value set with the time setting knob, the star operation output will be turned OFF and there will be delta operation output after the set star-delta transfer time has elapsed.

Page 35 Star-delta transfer time selector Star operation time range selector select one from 0. Before ordering, please check the List of Models on page 37 for availability.

Page 38 Note: 1. Be sure to secure the above minimum power ON time. Do not use the Timer with a repeat period of less than 3 s. Doing so may result in abnormal heating or burning.

Page 40 Turns off the control output and resets the elapsed time. Outputs Control output Operates instantaneously when the power is turned on and time-limit resets when the set time is up after the power is turned off. Do not use them as relay terminals. If the power ON time is less than this value, the Timer may not operate i.

Model Timing chart Page 43 Page 44 If it is required that the output be turned on repeatedly with an inter- Do not attempt to connect any input terminal to any terminal other val of shorter than 3 s, consider use of the H3CR-A in mode D signal than the input terminal or to apply voltage across other than the OFF-delay.

Page 46 A star operation time range 0 to 6, 0 to 12, 0 to 60, or 0 to A time range 0 to 0. Two, 4. Outputs Control output Operates instantaneously when the power is turned on and time-limit resets when the set time is up after the power is turned off. Do not use them as relay terminals. If the power ON time is less than this value, the Timer may not operate i. Model Timing chart Page 43 Page 44 If it is required that the output be turned on repeatedly with an inter- Do not attempt to connect any input terminal to any terminal other val of shorter than 3 s, consider use of the H3CR-A in mode D signal than the input terminal or to apply voltage across other than the OFF-delay.

Page 46 A star operation time range 0 to 6, 0 to 12, 0 to 60, or 0 to A time range 0 to 0. Two, 4. Use the Page 51 H3CR-F models at the lowest selector setting. Doing so may result in damage to contacts. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. Print page 1 Print document 53 pages. Rename the bookmark. Delete bookmark?

Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL. Timing operation is stopped and the control output turns OFF it is reset.

Gate The timing operation is interrupted while the gate input is active. Outputs Control output Outputs are turned ON according to designated output mode when preset value is reached.

The delayed contact of conventional Timers was indicated as The contact symbol of the H3CR-A is indicated as because its operating mode is six multi-modes four multi-modes for the H3CR-A8.

Terminal 5 is empty. No-contact Input Connection to a voltage output sensor. Contact Use contacts which can input adequately switch 0. Voltage imposition or open. Note: The input circuit is isolated from the Note: Refer to the signal levels in the power supply circuit. Thus, an NPN following table and be aware of the transistor can be connected. Voltage Input Signal Levels No-contact 1.

Transistor ON input Residual voltage: 1 V max. The voltage between terminals 6 and 7 must be Transistor OFF Leakage current: 0. The voltage between terminals 6 and 7 must be 1. Contact Use contacts that can adequately switch 0. Previous start input will be cancelled.

Note: The set time is the sum of t1 and t2. Start and reset are also both enabled when the gate signal is ON. Output indicator orange Lit when output Time range selector select one from 1. Scale range display windows changes as below by turning the Time range selector clockwise.

You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file.

Get 1 for every download of your manual. Buy as much as you need. The operating modes are as follows. DIN track mounting, surface mounting, and flush mounting.